kozy heat MINNETONKA 55345-RF Скачать руководство пользователя

Страница: 39 / 67

1. Place millivolt board in firebox, aligning the holes in the millivolt board with

holes in the firebox bottom. MAKE SURE SEALING GASKET IS IN PLACE
ON FIREBOX BOTTOM! Secure millivolt board to firebox bottom with the (8)
screws previously removed.

2. Place venturi spacers onto venturi mounting studs.

3. Re-install front burner assembly, making sure burner tube is positioned over

burner orifice. Secure with screws previously removed.

4. Reinstall back burner/log grate assembly by positioning burner tube into venturi

collar on millivolt board and pilot assembly through rectangular opening. Secure
front left and back right legs with screws previously removed.

5. Reinstall pilot shield.

6. Reinstall ember refractory.

7. Reinstall log set. (Pages 32-34).

8. Reconnect gas line to manual shut-off valve.

Model 55345:

Reconnect any wall switch, remote control or thermostat wires to the top &
bottom terminals on the gas valve.

Model 55245-RF:

Re-connect the (2) wires to fan cord. Plug fan cord into receptacle.

10. Reinstall glass frame assembly. Page 15.

11. Reinstall upper louver & upper hood. Page 37.

12. Turn gas on.

13. Verify proper log placement, operation of fireplace, and any electrical

components.

WARNING: DO NOT OPERATE THIS FIREPLACE WITHOUT SEALING GASKET (LOCATED UNDER THE MILLIVOLT BOARD) IN PLACE.

IF GASKETING IS DAMAGED, IT MUST BE REPLACED.

CAUTION: CHECK ALL CONNECTIONS FOR LEAKS, WHETHER

FIELD OR FACTORY MADE.

MILLIVOLT BOARD INSTALLATION

PAGE 36

RE-CONNECT ANY REMOTE /

THERMOSTAT WIRES

INSTALL (8) SCREWS

INSTALL (2) SCREWS

BURNER LOG GRATE ASSEMBLY

PILOT SHIELD

FRONT BURNER ASSEMBLY

Содержание MINNETONKA 55345-RF




































































Результаты поиска

Содержание MINNETONKA 55345-RF

Отзывы:

Похожие инструкции для MINNETONKA 55345-RF

Бренды по названию

Популярные бренды

kozy heat MINNETONKA 55345-RF, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MINNETONKA 55345-RF

Отзывы:

Похожие инструкции для MINNETONKA 55345-RF

Бренды по названию

Популярные бренды