kozy heat MINNETONKA 55345-RF Скачать руководство пользователя страница 12

Страница: 12 / 67

PREPARE THE FIREPLACE

The top stand-off brackets are attached to the fireplace top in a flat state for shipping.

1. Remove and save the (4) screws securing stand-off heat shield and stand-off brackets and the (4 screws located under stand-off brackets.

2. Form each stand-off bracket as shown.

3. Re-attach stand-off brackets to fireplace using screws previously removed.

CAUTION: NEVER PERMANENTLY REMOVE THESE
ASSEMBLIES FROM THE FIREPLACE - THEY MUST BE
SECURED IN PLACE REGARDLESS OF FINISH MATERIAL USED.

STAND-OFF ASSEMBLY & INSTALLATION

IMPORTANT: THE TOP STAND-OFF BRACKETS MUST BE FORMED AND ATTACHED PRIOR
TO POSITIONING THE FIREPLACE INTO FRAMED OPENING.

WARNING:
NON-COMBUSTIBLE ZONE: STAND-OFFS PROVIDE THE 10” (254 mm)
MINIMUM CLEARANCE TO HEADER. USE ONLY NON-COMBUSTIBLE
MATERIAL IN  THIS AREA FOR THE ENTIRE WIDTH OF FIREPLACE.

DO NOT USE WOOD, SHEETROCK ETC. IN THIS ZONE.

NOTE: OTHER CLEARANCES MUST BE MAINTAINED.
REFER TO PAGE 14

FOR MORE INFORMATION.

STAND-OFF BRACKETS

AS SHIPPED

REMOVE SCREWS SECURING

EACH STAND-OFF BRACKET

ATTACH BOTH STAND-OFF BRACKETS BY
ALIGNING WITH HOLES IN FIREPLACE TOP.
SECURE WITH (4) SCREWS AS SHOWN.

FORM STAND-OFF BY BENDING AT

PERFORATIONS AS SHOWN

FORMED STAND-OFF

STAND-OFF BRACKETS

INSTALLED

CAUTION: STAND-OFF BRACKETS
ARE NOT LOAD BEARING.

PAGE 9

Содержание MINNETONKA 55345-RF




































































Результаты поиска

Содержание MINNETONKA 55345-RF

Отзывы:

Бренды по названию

Популярные бренды

kozy heat MINNETONKA 55345-RF, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MINNETONKA 55345-RF

Отзывы:

Бренды по названию

Популярные бренды