KONRAD Series 600B Скачать руководство пользователя

Страница: 57 / 77

600B SERIES MAINTENANCE MANUAL

JULY 2016 - V1.0

PAGE 51

Trim/Lift Electrical Drawing (12 Volt) single drive, single helm

AUX

BAT

BREAKER 5A

PUMP MOTOR

CONNECT TO NEGATIVE/GROUND SIDE OF 12VDC CIRCUIT

CONNECT TO POSITIVE SIDE OF 12VDC CIRCUIT (100 AMP)

POWER RELAY (UP)

POWER RELAY (DN)

OIL RESERVOIR SWITCH

RUDDER SENSOR

K.M. P/N 13-554

TRIM SENSOR

K.M. P/N 13-554

SEAL PLUG 13-445

MODULE #1

K.M. P/N 13-543

*11

*12

SEAL PLUG 13-445

CONNECTING

HARNESS

10' K.M. P/N 31-057 20' K.M. P/N 31-058 30' K.M. P/N 31-059 40' K.M. P/N 31-060

DIGITAL DISPLAY

K.M. P/N 13-544

TRIM/ LIFT PUMP ASSEMBLY

K.M. P/N 31-048

KONRAD MARINE INC.

TRIM SYSTEM ELECTRICAL

DRAWING (12 VOLT)

600B SINGLE

NOTES: 1) WIRE IDENTIFICATIONS ARE LABELED AS: BK=BLACK, BL=BLUE, RD=RED, PR=PURPLE, GR=GREEN, OR=ORANGE, WT=WHITE, GY=GRAY YL=YELLOW, TN=TAN, BR=BROWN, PK=PINK

2) ALL WIRES PASSING THROUGH THE CONNECTORS REMAIN THE SAME COLOR

HARNESS K.M. P/N 31-054

*10

*13

*14

RESISTOR K.M. P/N 13-599

TWISTED PAIR WIRE

DRAWING BY A.G. AUGUST 2015

MOMENTARY (ON) OFF (ON) TOGGLE SWITCH TRIM OVER RIDE

K.M. P/N 13-438

K.M. P/N 11-065

TWISTED PAIR WIRE

6 POSITION TERMINAL STRIP K.M. P/N 11-069

4 POSITION TERMINAL STRIP K.M. P/N 11-070

K.M. P/N 10-528

NOTE:CONDUCTORS WIRES NOT SUPPLIED BY KONRAD MARINE

Y-CONNECTOR K.M. P/N 13-457

HARNESS K.M. P/N 31-051

HOT/POSITIVE (8-32V)

THROTTLE TRIM 1 (DN)

THROTTLE TRIM 1 (UP)

PANEL ILLUMINATION

KEYSWITCH

SEAL PLUG K.M. P/N 13-445

NEGATIVE/GROUND

NOTES FOR HARNESS 31-054: 1) ALL WIRES ARE PIGAILED AND TO BE ROUTED/CONNECTED TO DESIGNA

TED LOCATION.

2) ALL THROTTLE CONTOL WIRES ARE INCLUDED; HOWEVER, NOT ALL APP

LICATIONS WILL

UTILIZE ANY OR ALL OF THE WIRES. 3) SET 1 FOR SINGLE, SET 1,2 FOR TWIN, SET 1,2,3 FOR TRIPLE APP

LICATION. THIS IS

INDICATING THAT EACH DRIVE HAS ITS OWN TRIM CONTROL SWITCH. 4) IF YOUR APPLICATION IS A TWIN OR TRIPLE BUT ONLY UTILIZES ON

E THROTTLE

CONTROL(DRIVES ARE SYNCHRONIZED) SET 1 FOR SINGLE.

THROTTLE TRIM 3 (DN)

THROTTLE TRIM 3 (UP)

THROTTLE TRIM 2 (DN)

THROTTLE TRIM 2 (UP)

K.M. P/N 10-430

CONNECTOR *#

DESCRIPTION

MATING

CONNECTOR

18 CAVITY FEMALE

18 CAVITY MALE

3 CAVITY MALE

3 CAVITY/ 3 WAY FEMALE Y-CONNECTOR

*3,*5,*6

3 CAVITY MALE

3 CAVIY MALE

3 CAVITY MALE

3 CAVITY/ 3 WAY FEMALE Y-CONNECTOR

*7,*9,*10

3 CAVITY MALE

*10

3 CAVITY MALE

*11

12 CAVITY FEMALE

*12

12 CAVITY MALE

*11

*13

12 CAVITY MALE

*14

12 CAVITY FEMALE

*13

DRAWING NO.

Chapter 3 - Complex Maintenance

(

continued)

Содержание Series 600B














































































Результаты поиска

Содержание Series 600B

Отзывы:

Похожие инструкции для Series 600B

Бренды по названию

Популярные бренды

KONRAD Series 600B, Руководство по обслуживанию

Результаты поиска

Содержание Series 600B

Отзывы:

Похожие инструкции для Series 600B

Бренды по названию

Популярные бренды