KONRAD Series 600B Скачать руководство пользователя

Страница: 42 / 77

600B SERIES MAINTENANCE MANUAL

JULY 2016 - V1.0

PAGE 36

Bellows

Description and Parts Breakdown

Individual Components

Description

Quantity

Part #

Bellows

10-230

Hose clamp

10-336

Inspection

Look for any cracks, holes, tears or a broken seal.
Look for large amount of corrosion on the surface of material or excessive wear.

Removal & Installation - Bellows

NOTE

Sterndrive must be removed for removal and installation of bellows.

Remove U-joint bellows from gimbal housing by loosening the two (2) hose clamps (10-336).

Position ground clips on bellows.

Position u-joint bellows with “TOP” mark facing upwards and install u-joint bellows on gimbal housing

flange and position clamp. Torque to 30-40 lb. in. (3.4 - 4.5 Nm).

NOTE

: When ordering the bellows (10-230), the two (2) hose clamps (10-336) are included.

IMPORTANT:

Be sure that the bead on the inner mating surface of bellows is positioned in the groove on

the gimbal-housing flange.

Bellows

10-230

Hose Clamp

10-336

Chapter 3 - Complex Maintenance

Содержание Series 600B














































































Результаты поиска

Содержание Series 600B

Отзывы:

Похожие инструкции для Series 600B

Бренды по названию

Популярные бренды

KONRAD Series 600B, Руководство по обслуживанию

Результаты поиска

Содержание Series 600B

Отзывы:

Похожие инструкции для Series 600B

Бренды по названию

Популярные бренды