background image

600B SERIES MAINTENANCE MANUAL

JULY  2016 - V1.0

PAGE 55

AUX

BAT

BREAKER

5A

PUMP MOTOR

POWER RELAY (UP)

RUDDER  SENSOR

K.M. P/N 13-554

TRIM  SENSOR

K.M. P/N 13-554

1

6

7

MODULE #1

K.M. P/N 13-543

6

7

1

12

*11

DIGITAL DISPLAY

K.M. P/N 13-544

TRIM/ LIFT PUMP ASSEMBLY

K.M. P/N 31-048

NOTES: 1) WIRE IDENTIFICATIONS ARE LABELED AS: BK=BLACK, BL=BLUE, RD=R

ED, 

PR=PURPLE, GR=GREEN, OR=ORANGE, WT=WHITE, GY=GRAY YL=YELLOW, TN=TAN, BR=BROWN, PK=PINK

2) ALL WIRES PASSING THROUGH THE CONNECTORS REMAIN THE SAME  COLOR

3) MODULE #1 CONNECTS TO THE PORT DRIVE TRIM PUMP, MODULE #2  CONNECTS TO THE CENTER DRIVE TRIM PUMP, MODULE #3 CONNECTS TO  THE STARBOARD DRIVE TRIM PUMP.

*14

GR

BL

DRAWING BY A.G. AUGUST 2015

K.M. P/N  13-438

K.M. P/N  11-065

1

2

3

4

5

6

1

2

3

4

5

6

1

1

2

2

3

3

4

4

BK

BK

HARNESS K.M. P/N 31-051

*13

12

1

12

1

12

K.M. P/N 13-610

K.M. P/N 13-585

KEYPAD

THROTTLE TRIM 2 (UP)

THROTTLE TRIM 2 (DN)

THROTTLE TRIM 3 (DN)

NEGATIVE/ GROUND

HOT/ POSITIVE (8-32V)

KEYSWITCH

PANEL ILLUMINATION

THROTTLE TRIM 1 (UP)

THROTTLE TRIM 1 (DN)

3

2

4

1

2

1

4

3

NEGATIVE/ GROUND

HOT/ POSITIVE (8-32V)

OIL  RESERVOIR   SWITCH

CONNECT TO  NEGATIVE/GROUND SIDE OF 12VDC CIRCUIT

CONNECT TO POSITIVE  SIDE OF 12VDC CIRCUIT 100(AMP)

NOTE: CONDUCTOR WIRES NOT SUPPLIED  BY KONRAD MARINE

TRIM PUMP #1

A

B

C

A

B

C

A

B

C

A

B

C

A

B

C

C

A

B

A

B

C

A

C

A

B

C

A

B

C

A

B

C

A

B

C

C

B

A

C

B

A

B

C

A

A

C

B

A

C

A

B

C

A

B

C

C

C

A

B
A

B

C

A

B

A

B

C

6

12

18

13

7

1

1

7

13

6

12

18

7

6

6

7

RD

BK

SEAL PLUG 13-445

SEAL PLUG 13-445

SEAL PLUG 13-445

BK

BK

YL

RD

BK

YL

RD

RD

RD

RD

RD

YL

PR

PR

4 POSITION TERMINAL STRIP K.M. P/N 11-070

YL

PR

YL

GY

RD

PK

BL

TN

GR

BL

RD

BK

RD

BK

GR

GY

TN

WT

PK

OR

PR

YL

CONNECTING

HARNESS

10' K.M. P/N 31-057 20' K.M. P/N 31-058 30' K.M. P/N 31-059 40' K.M. P/N 31-060

CONNECTING 

HARNESS

6' K.M. P/N 31-061 10' K.M. P/N 31-057 14' K.M. P/N 31-062

CONNECTING

HARNESS

K.M. P/N 31-071

*1

*2

*4

*5

*6

*7

*8

*9

*12

*10

*21

*22

*19

*20

*17

*16

*18

*15

*27

*28

K.M. P/N 10-528

POWER RELAY (DN)

K.M. P/N 10-430

THROTTLE TRIM 3 (UP)

B

*24

*23

*25

*26

C

A

B

C

A

B

A

C

B

A

B

C

A

B

C

C

B

A

B

A

C

*3

CONNECTING HARNESS FROM TRIM PUMP #2 & MODULE #2 (13-697)

CONNECTING HARNESS FROM TRIM PUMP #3 & MODULE #3 (13-698)

B

CONNECTING 

HARNESS

6' K.M. P/N 31-061 10' K.M. P/N 31-057 14' K.M. P/N 31-062

CONNECTING 

HARNESS

4' K.M. P/N 31-108

KONRAD MARINE INC. TRIM SYSTEM ELECTRICAL  DRAWING (12 VOLT) 600B TRIPLE

MOMENTARY (ON) OFF (ON)  TOGGLE SWITCH TRIM OVER RIDE

BK

BK

6 POSITION  TERMINAL STRIP K.M. P/N 11-069

HARNESS K.M. P/N 31-054

NOTES FOR HARNESS 31-054: 1) ALL WIRES ARE PIGAILED AND TO BE ROUTED/CONNECTED TO DESIGNA

TED LOCATION.

2) ALL THROTTLE CONTOL WIRES ARE INCLUDED; HOWEVER, NOT ALL APP

LICATIONS WILL 

UTILIZE ANY OR ALL OF THE WIRES. 3) SET 1 FOR SINGLE, SET 1,2 FOR TWIN, SET 1,2,3 FOR TRIPLE APP

LICATION. THIS IS 

INDICATING THAT EACH DRIVE HAS ITS OWN TRIM CONTROL SWITCH.  4) IF YOUR APPLICATION IS A TWIN OR TRIPLE BUT ONLY UTILIZES ON

E THROTTLE 

CONTROL(DRIVES ARE SYNCHRONIZED) SET 1 FOR SINGLE. 

RESISTOR K.M. P/N  13-599

RESISTOR K.M. P/N  13-599

CONNECTOR *#

DESCRIPTION

MATING 

CONNECTOR

*1

18 CAVITY FEMALE

*2

*2

18 CAVITY MALE

*1

*3

3 CAVITY MALE

*4

*4

3 CAVITY/ 3 WAY FEMALE Y-CONNECTOR

*3,*5,*6

*5

3 CAVITY MALE

*4

*6

3 CAVITY MALE

*4

*7

3 CAVITY MALE

*8

*8

3 CAVITY/ 3 WAY FEMALE Y-CONNECTOR

*7,*9,*10

*9

3 CAVITY MALE

*8

*10

3 CAVITY MALE

*8

*11

12 CAVITY MALE

*12

*12

12 CAVITY MALE

*11

*13

12 CAVITY FEMALE

*14

*14

3 CAVITY MALE

*13

*15

3 CAVITY MALE

*16

*16

3 CAVITY/ 3 WAY FEMALE Y-CONNECTOR

*15,*17,*18

*17

3 CAVITY MALE

*16

*18

3 CAVITY MALE

*16

*19

3 CAVITY MALE

*22

*20

3 CAVITY  MALE

*22

*21

3 CAVITY MALE

*22

*22

3 CAVITY/ 3 WAY FEMALE Y-CONNECTOR

*19,*20,*21

*23

3 CAVITY MALE

*25

*24

3 CAVITY MALE

*25

*25

3 CAVITY/ 3 WAY FEMALE Y-CONNECTOR

*23,*24,*26

*26

3 CAVITY MALE

*25

*27

4 CAVITY MALE

*26

*28

4 CAVITY FEMALE

*26

DRAWING NO.

Trim / Lift Electrical Drawing (12 Volt) triple drive, single helm

Chapter 3 - Complex Maintenance 

(continued)

Содержание Series 600B














































































Отзывы: