KONRAD Series 600B Скачать руководство пользователя

Страница: 51 / 77

600B SERIES MAINTENANCE MANUAL

JULY 2016 - V1.0

PAGE 45

Removal

1. Remove four (4) (12-839) S.H.C.S. using a standard allen socket wrench.

2. Using a needle nose pliers, remove tab washer (12-838).

3. Remove outer retaining nut (12-954) from lower housing using tool TO-142. Turn counter clockwise

to loosen. Remove carrier (12-510) from lower housing using tool TO-151.

4. Remove retaining nut (12-513) from lower housing using tool TO-119. Turn counterclockwise to

loosen.

5. Remove forward propeller shaft assembly (12-502) by pulling straight out and over the aft propeller

shaft. The race of bearing (12-521) from the lower housing should pull out with this assembly.

NOTE

The gear assembly and thrust cap will come out with the propeller shaft as they are assembled to

the shaft.

6. Recover shims (12-515) from lower housing and/or stuck to bearing race.

Rebuilding

1. Remove both seals (12-517) and (12-525) from propeller shaft assembly (12-502) using slide hammer

TO-028.

NOTE

Be careful not to damage surface of thrust cap on the opposite end of the propeller shaft.

Protect with some sort of cloth.

2. Clean propeller shaft assembly (12-502) thoroughly.

3. Apply red

Loctite

263 to outside of first seal (12-525) and grease inner seal surface. Press into

propeller shaft using long end of tool TO-116. Apply red

Loctite

263

to outside of second seal

(12-517) and grease inner seal surface. Press into propeller shaft using opposite side of tool TO-116.

Fill space in between two seals with grease.

4. Remove both seals (12-518) and (12-526) from carrier (12-510) using punch or slide hammer

TO-028.

5. Remove o-ring (12-527) from carrier (12-510).

6. Clean carrier unit (12-510) thoroughly.

7. Place new o-ring (12-527) in groove on carrier and grease o-ring.

8. Apply red

Loctite

263 to outside of first seal (12-526) and grease inner seal surface. Press into carrier

unit using long end of tool TO-117. Apply red

Loctite

263 to outside of second seal (12-518) and

grease inner seal surface. Press into carrier unit using opposite side of tool TO-117. Fill space in

between two seals with grease.

Chapter 3 - Complex Maintenance

(continued)

Содержание Series 600B














































































Результаты поиска

Содержание Series 600B

Отзывы:

Похожие инструкции для Series 600B

Бренды по названию

Популярные бренды

KONRAD Series 600B, Руководство по обслуживанию

Результаты поиска

Содержание Series 600B

Отзывы:

Похожие инструкции для Series 600B

Бренды по названию

Популярные бренды