KNEGT 504G3 Series Скачать руководство пользователя

Страница: 38 / 111

504G3

SERIES TRACTOR OPERATION MANUAL

Left and Right Turn Indicators (Green)

Left and right turn indicators lights when left or right indicator

lamp is lit.

Brake Indicator (Red)

Brake indicator lights when brake is depressed. At one time, the

brake lamp will light.

PTO Monitor Indicator for 540 rpm

Indicates the state of the PTO shaft as follows:

–

If the monitor glows, the PTO shaft is rotating at speed of 540 rpm.

PTO Monitor Indicator for 1000 rpm

Indicates the state of the PTO shaft as follows:

–

If the monitor glows, the PTO shaft is rotating at speed of 1000 rpm

Electrical preheat Indicator

When ignition switch is on ‘Preheat’ position, thi indicates is working.

Headlight Indicator and Tail Lamp Indicator

Headlight Indicator should glow when Headlight switch is switched

to beam position.

Tail Lamp Indicator

should glow when Tail Lamp switch is switched

to beam position.

、

Combination Switch

：

Fig.4-5 Combination switch

1. Turn indicator switch

2. Horn switches

3. Main beam switch

Turn indicator switch 1 is used to switch on the right or left turn indicator lamp. Turn

switch 1 clockwise to switch on right indicator lamp. Turn button 1 counterclockwise to

switch on the left indicator lamp. Turn indicator switch is not functional when hazard

warning signals flashing.

Switch off hazard warning signal with hazard warning switch before operating turn

Содержание 504G3 Series
















































































































Результаты поиска

Содержание 504G3 Series

Отзывы:

Похожие инструкции для 504G3 Series

Бренды по названию

Популярные бренды

KNEGT 504G3 Series, Руководство по эксплуатации

Результаты поиска

Содержание 504G3 Series

Отзывы:

Похожие инструкции для 504G3 Series

Бренды по названию

Популярные бренды