KNEGT 504G3 Series Скачать руководство пользователя

Страница: 85 / 111

504G3

SERIES TRACTOR OPERATION MANUAL

7.4 Braking system

Troubles & possible causes

Fixing methods

(1) Brake fails

①

The brake disk is worn seriously, or worn
eccentrically.

②

Free path of brake pedal is too large

①

Put air out of pipe

②

Readjust

(2) Tractor steer wander during braking

①

The left and right brake pedals’ free
pathes are different

②

The brake disk is damaged in one side

③

Air pressures in the two rear tires are
different

①

Adjust

②

Replace

③

Check up and air up the tires as
per regulation

(3) The tractor is shivering at starting

①

The brake pedals’ free pathes is too small

②

Return spring’s pressure is too small

①

Adjust

②

Replace

(4) The brake cannot be separated completely

and resulting in heat

①

Grip brake still under operational

②

The brake pedals’ free pathes is too small

①

Loosen the grip brake

②

Adjust

7.5 Front driven axle (4WD)

Troubles & possible causes

Fixing methods

(1) The front tires are worn seriously

①

The front wheel rim or supporter
deformed seriously

②

The front wheel toe-in adjust improperly

③

The steering knuckle and two pins of oil
cylinder are worn seriously

④

The air pressure is insufficient and the
front axle is engaged when transporting

①

Correct them

②

Adjust tor-in

③

Replace pintles

④

Checkup and air up and
disconnect

(2) The front wheels are swaying

①

Bearing of front driven axle is abraded
heavily

②

Bearing of steering knuckle is abraded
heavily

③

Clearance of front and rear supporting
seat is too large

④

The front wheel rim deformed seriously

⑤

The front wheel toe-in adjust improperly

①

Replace

②

Replace

③

Adjust

④

Correct

⑤

Adjust

Содержание 504G3 Series
















































































































Результаты поиска

Содержание 504G3 Series

Отзывы:

Похожие инструкции для 504G3 Series

Бренды по названию

Популярные бренды

KNEGT 504G3 Series, Руководство по эксплуатации

Результаты поиска

Содержание 504G3 Series

Отзывы:

Похожие инструкции для 504G3 Series

Бренды по названию

Популярные бренды