KNEGT 504G3 Series Скачать руководство пользователя

Страница: 7 / 111

504G3

SERIES TRACTOR OPERATION MANUAL

Chapter

Safety

Precautions

1.1 Safety Instructions

1.1.1

Safety

first

The respect of the rules for tractor use, maintenance and repair given in this manual is

an essential element for the correct use of the tractors as envisioned by the

manufacturer.

Carefully read all safety messages in this manual and on your

machine safety signs.Replace missing or damaged safety signs.Be

sure new equipment components and repair parts include the

current safety signs.Replacement safety signs are available

from your

Knegt

dealer.

Learn how to operate the machine and how to use controls properly.Do not let anyone

operate without instruction.

Keep your machine in proper working condition.Unauthorized modifications to the

machine may impair the function and safety and affect service life of machine.

Lightning and high voltage cable can kill you. Do not use the machine if there is

lightning in your area or under high voltage cable.

Handle fuel carefully, it is highly flammable.Do not refuel the machine while

smoking or when near open flame or sparks.

Always stop the engine before refueling machine.Fill fuel tank outdoors.

Prevent fires by keeping machine clean of accumulated trash, grease, debris.Always

clean up spilled fuel.

Please remember that you will undertake the personal responsibility for any

associated consequences with the improper use of these tractors.

All the time you are

working with or on the machine, take care and stay alert. Always be careful. Always be

alert for hazards.

It is extremely dangerous to operate machinery when under the influence of alcohol

or drugs. Do not drink excessively or take drugs before or while operating the machine

or attachments. Be aware of medicines which can cause drowsiness.

Содержание 504G3 Series
















































































































Результаты поиска

Содержание 504G3 Series

Отзывы:

Похожие инструкции для 504G3 Series

Бренды по названию

Популярные бренды

KNEGT 504G3 Series, Руководство по эксплуатации

Результаты поиска

Содержание 504G3 Series

Отзывы:

Похожие инструкции для 504G3 Series

Бренды по названию

Популярные бренды