KNEGT 504G3 Series Скачать руководство пользователя

Страница: 12 / 111

504G3

SERIES TRACTOR OPERATION MANUAL

parts or components.

3. Before disconnecting any hydraulic line or hose, make sure the system is

pressure-free.

4. Hydraulic oil escaping under pressure can cause serious personal injury. When

searching for or detecting oil leaks, make sure to use adequate safety protection

such as shields, goggles and gloves.

5. Prior to inspection, cleaning, adjustment or maintenance of the tractor or any

mounted or connected implement, always make sure that engine is shut off. Also

make sure the transmission is in neutral, the brakes

are locked, the power take-off (PTO) is disengaged

and all other moving parts are stationary.

6. Do not fill fuel tank completely when expecting to

work in full sunlight because the fuel might expand

and escape. In such case, promptly wipe off

any fuel that has escaped.

7. Tractor fuel may be dangerous. Never refuel

while engine is running, is still hot, or you are

near an open flame or when someone is

smoking.

8. Do not service the tractor while it is in motion or while the engine is running

．

When

servicing front-wheel-drive-equipped tractor with rear wheels supported off ground

and rotating wheels by engine power

，

always

support front wheels in a similar

manner

．

Engaging front-wheel drive will pull rear

wheels off support if front wheels are not

raised

．

Tighten wheel hardware to correct torque

as specified in Wheels

，

Tires and Tread

section

．

Torque at intervals shown in Break-In

Period and Lubrication and Maintenance sections

，

to ensure that wheel hardware

does not loosen

．

Reinstall protective covers removed during service

．

9. Do not work on tires unless suitable tools are available and you have the training

Содержание 504G3 Series
















































































































Результаты поиска

Содержание 504G3 Series

Отзывы:

Похожие инструкции для 504G3 Series

Бренды по названию

Популярные бренды

KNEGT 504G3 Series, Руководство по эксплуатации

Результаты поиска

Содержание 504G3 Series

Отзывы:

Похожие инструкции для 504G3 Series

Бренды по названию

Популярные бренды