manualshive.com logo in svg

KM SVS2000, Руководство по установке и эксплуатации, Страница: 24 / 89

Поделиться
Скачать
KM SVS2000 Скачать руководство пользователя страница 24

20

97-1129-01 Rev. D

www.kistlermorse.com

quIcK conFIguraTIon procedure

1.  Apply power to the unit while pressing the enter key. The display shows:

 

QUICK COnFIG

 

PRESS EnTER...

 

...TO COnTInUE

2.  Press the enter key. The display shows:

 

UnITS? lbs

The choices for units are lbs or kg. For kg, press the up Arrow key; the display shows:

 

UnITS? kg

note: you can change units after Quick Config is complete.

3.  When the display shows the desired units, press the Enter Key. The display acknowledges the selection 

and shows:

 

km BOLT-On?

The choices for sensor type are K-M bolt-on or direct support. For direct support sensors, press the Up 

Arrow key;the display shows:

 

DIRECT SUPPORT?

4.  When the display shows the desired sensor type, press the Enter Key. The display acknowledges the selection.

 

•  For km bolt-on sensors, proceed to Step 5.

 

•  For direct support sensors, proceed to Step 16.

5.  If you selected km Bolt-On, the display shows:

 

L-CeLLs?

The choices for km bolt-on sensor are L-Cells or microcells. For microcells, press the up Arrow key; the 
display shows:

 

mICrOCeLLs?

6.  When the display shows the desired bolt-on sensor, press the Enter Key. The display acknowledges the 

selection.

 

•  For L-Cells, proceed to Step 11.

 

•  For microcells, proceed to Step 7.

7.  If you selected microcells, the display shows:

 

HOrIZOnTL BeAmS?

The choices for location are horizontal beams or vertical legs. For vertical legs, press the up Arrow key; 
the display shows:

 

verTICAL LegS?

8.  When the display shows the desired Microcell location, press the Enter Key. The display acknowledges 

the selection.

 

•  For microcells on horizontal beams, proceed to Step 11.

 

•  For microcells on vertical legs, proceed to Step 9.

Содержание SVS2000


























































































Отзывы:

Нет отзывов