KiSS ORCA SPIRIT, Руководство пользователя

Страница: 48 / 124

48 MSL 72.161 Jetsam/Orca Spirit manual R.5
MOUTHPIECE REASSEMBLY
Dive Rite or Apeks Second Stage

Inspect the mushroom valve carriers and the mushroom valves for damage. Ensure that they are clean, washed
and disinfected, and remove any debris. IF THE MUSHROOM VALVES ARE DISTORTED OR DAMAGED THEY MUST
BE REPLACED!!! When a aching (or removing) the mushroom valves BE CAREFUL!!! PULL ON THE STEM GENTLY &
ONLY HOLD THE STEM WHEN REMOVING THE VALVE.

Ensure that the mushroom valve carrier O‐rings are clean, free of debris and in good condi on. Lubricate the O‐
rings and insert them onto the carriers. These O‐rings need only LIGHT lubrica on.

Clean, disinfect and inspect the mouthpiece body. Hold the body with the rubber mouth bite towards you and the
port for the 2nd stage regulator facing down. Posi on the right side mushroom valve carrier with the valve facing
out. This is the exhale side and you will no ce that this valve does not have a stem showing. Posi on the le side
mushroom valve carrier with the valve on the inside of the carrier. You will no ce that the le side valve has the
stem facing out. Ensure that the O‐rings do not extrude out of their grooves when you push them into place. Push
the carriers all the way in, un l you feel them push against the body. These mushroom valves have a higher cost
then those for the older KISS mouthpiece; be gentle with them!

Clean, disinfect and inspect the inner barrel and the inner barrel O‐rings for damage. There are 2 side port O‐rings
and 2 end O‐rings. Lubricate these O‐rings, place them in their grooves, and then apply a touch more lubricant. If
upon tes ng small leaks are apparent, applying silicone grease to the inner barrel O‐rings could solve this problem.
Apply lubricant only to the O‐ring areas; clean off the excess from the surrounding areas. Lubricant on the non O‐
ring areas of the inner barrel will make it difficult to turn the switch!

To make the inner barrel easier to insert, the switch can be pushed onto the barrel stub. Insert the barrel, twis ng
it slightly to ensure the port side O‐rings do not move out of their grooves. Push and turn the barrel so it moves
properly into posi on. Watch the O‐rings while you do this, to ensure that they stay in posi on.

Replace the front cover, ensuring that it is securely a ached, but not over ghtened. If it is over ghtened, it will
be difficult to remove.

Replace the switch. Once the switch is a ached, rotate it from open to closed circuit mode and back, several mes
to ensure correct ac on of the O‐rings. Do this while looking into the second stage port to ensure that the O‐rings
stay in their grooves.

Clean, inspect and re‐fit the 4 hose a achment O‐rings; there are 2 per side.

Clean, disinfect and inspect the 2 hose a achments and secure them to the mouthpiece using the 2 plas c U‐clips.
To a ach, push the hose a achments all the way against the body, and then push the clip into the slots. The hose
a achments have a ght fit. When pushing them into posi on, be certain that the O‐rings are not dislodged from
their grooves. Applying a touch of lubricant to the inside sealing area of the hose a achment may help in pushing
it into posi on.
*NOTE: when a aching and removing the mouthpiece from the loop hoses, the quick disconnects should be used.
Do not use the hose a achments and plas c clips for this.
Clean, disinfect and inspect the rubber mouth bite. A ach it to the body using a zip e and remove the sharp edges.