manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, Руководство пользователя

Поделиться
Скачать
Kirby Morgan M-48 SuperMask Скачать руководство пользователя страница 9

Introduction

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

 

9

B

 

WARNING

Cold Water Diving (water Temperatures below 50 °F 10 °C) 

requires specialized training and equipment. Do not at-

tempt diving in cold water unless you are properly trained 

and equipped for this type of specialized diving. Attempting 

to dive cold waters without proper training & equipment 

can cause fatal accidents stemming from poor coordina-

tion, gear freeze-ups, hypothermia, etc.

B

 

DANGER

☣

BIOHAZARD

Kirby Morgan Dive Systems, Inc., cannot 
guarantee the diver protection from con-
taminants when using the M-48 SuperMask

®

 

in waters that are biologically, chemically or 
radioactively polluted. Radioactive, chemi-
cal, and biological contaminants can cause 
serious, permanent bodily harm or death to 
the user.

While the M-48 

SuperMask

®

 can minimize 

and help reduce the risks associated with the 
exposure to certain waterborne chemical and 
biological contamination, it cannot protect the 
user in all situations or against all contaminants 
and KMDSI makes NO claim that the mask will 
protect the diver while diving in contaminated 
water.

CORROSIVE

RADIOACTIVE

Diving this mask in water containing concentrations of petroleum based 
chemicals could cause degradation of the components of the mask. Clean 
the mask using only a solution of one tablespoon of mild hand dish wash-
ing soap, such as Joy or Palmolive, to one gallon of water.

Содержание M-48 SuperMask

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды