manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, Руководство пользователя

Поделиться
Скачать
Kirby Morgan M-48 SuperMask Скачать руководство пользователя страница 21

Pre-Dive

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

 

21

When the regulator/BOV/DSV is 

inserted into the pod, the mount 

tube of the regulator/BOV/DSV 

must be inserted as far as it 

will go into the pod

. In addition, 

the regulator /BOV/DSV must 

be oriented correctly, i.e., right 

side up & free of lubricants too.

B

 

WARNING

Use only a KMDSI tie wrap P/N 520-039 rated for a minimum 

pull of 50 lbs. Use of a weaker tie wrap, or one that is “LOW 

PROFILE” could become loose and allow the regulator to 

pull out of the pod. This could lead to flooding of the pod 

and death by drowning.

Use only a KMDSI tie wrap 

with a minimum pull rating 

of 50 lbs./22.6 kg

Tighten the tie wrap properly 

using a tie wrap gun to achieve 

the correct tension. If a tie-

wrap gun is not available, use 

needle nose pliers to tighten.

5.  Fit the tie wrap P/N 520-039 into position, ensure the joint of the tie 

wrap ends up in the center of the side of the mouth opening as shown 
pull tight as tight as possible by hand or use a tie wrap installation 

Содержание M-48 SuperMask

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды