manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, Руководство пользователя

Поделиться
Скачать
Kirby Morgan M-48 SuperMask Скачать руководство пользователя страница 22

Pre-Dive

22

 

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

tool. Cut off excess tie wrap material flush with the joint lock of the 
tie wrap. There should be no sharp edges.

6.  Pull the mouthpiece and the demand regulator/BOV/DSV in opposite 

directions with enough force to ensure that they are both securely 
mounted to the pod.

7.  If the mouthpiece or demand regulator/BOV/DSV pulls off the pod, 

even partially, it must be remounted!

It is recommended that any time a user is in doubt as to the integrity of 
the “component to pod” fit in question, a simple pull test be performed by 
the end user or installer. Attach a 25 lb./11.3 kg weight or a filled 50 cu. ft 
aluminum SCUBA tank to the demand regulator/BOV/DSV using string or 
tie wraps in the manner shown on this page. Suspend the weight for 3–5 
seconds from the pod with the pod mounted on a stable device, if available 
and allowing the full weight to pull on the demand regulator/BOV/DSV.

If there is any doubt regarding 

the mounting of the regulator, 

perform a pull test as illustrated 

here, by using a 25 lb./11.3 

kg weight, maximum. 

B

 

WARNING

After assembling, ensure the demand regulator/BOV/DSV 

functions properly without interference to or from any 

part of the pod or mask. If in doubt, do not use until first 

consulting with KMDSI or Dive Lab Inc. Signs of improper 

function, if ignored, may lead to compromised air delivery 

which could lead to accidents that can cause injury or 

death.

Содержание M-48 SuperMask

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды