manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, Руководство пользователя

Поделиться
Скачать
Kirby Morgan M-48 SuperMask Скачать руководство пользователя страница 36

Post Dive Procedures/Checklist

36

 

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

1. 

With the mouthpiece in your mouth begin exhaling through the nose. 

2.  While exhaling push on the tilt purge stem in any direction to activate 

the valve. 

3.  Repeat process until water is completely out of the pod.

Review: Dewatering pod
1. 

Exhale through the nose (with mouth closed or the mouthpiece in 
your mouth).

2.  If pod is equipped with tilt to purge activate valve while exhaling.

The lower cavity should be clear of water within two to three exhalations 
from the nose.

Remember…When air bubbles are seen or heard escaping out of the valve, 
that is indicating water has been purged from the pod.

Post Dive Procedures/Checklist

Completely inspect the SuperMask

®

, soft pod and all related gear after each 

dive in accordance with the checklist in the following “Post-Dive Cleaning 
and Inspection” to ensure that all components are in proper working order.

NOTE

For the following procedures, the SuperMask

®

 should already be 

completely disconnected from the breathing system.

Post-Dive Cleaning and Inspection

Kirby Morgan Dive Systems, Inc.

®

1430 Jason Way Santa Maria, California  93455

 Phone:  805/928-7772     Fax:  805/928-0342

www.KirbyMorgan.com   email: [email protected]

KI

RBY

 MORGA

N

  D

IV

E SYSTEMS, I

nc

.

© MMXVI Kirby Morgan Dive Systems, Inc.   All Rights Reserved       Document # 160824002 

Page 1 of 1

M-48 Post-Dive Cleaning and Inspection

Diver Name:  

    Date:   

N O.

ST E P

I N I T.

1. 

 

Remove pod from mask. 

2.   

Soapy Solution Wash: Prepare solution of warm water (80–100 °F) and mild hand type dish-
washing soap. Agitate components in solution for 2–3 minutes; use soft bristle brush or clean-
ing rag. Allow mask to soak for 10 minutes then rinse thoroughly with clean fresh water.

3.   

Ensure all debris such as sand and dirt is removed from regulator mouthpiece 
and BOV/DSV inhalation and exhalation ports. Clean the regulator; BOV or DSV 
IAW manufacturer’s instructions. Thoroughly rinse the tilt-to-purge valve.

4.   

Rotate Regulator Adjustment Knob fully out (counter clockwise), if equipped.

5.   

Gently blow dry mask and pod with clean, oil-free low pressure air (less than 30 psig, or 
1.8 bar) or hang and let air dry completely. Allow mask to dry completely before stor-
age. Avoid direct sunlight. To avoid spotting, dry view ports with a clean, lint free cloth.

6.   

Inspect mask for damaged, worn, or missing parts.

7.   

Dry and store mask and pod out of sunlight and fl uores-
cent light, preferably in protective bag or pouch.

Содержание M-48 SuperMask

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды