manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, Руководство пользователя

Поделиться
Скачать
Kirby Morgan M-48 SuperMask Скачать руководство пользователя страница 43

Adjustments and Minor Repairs

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

 

43

8.  Using tie wrap tool or equivalent, 
install new tie wrap to secure Purge 
Tube in place on pod skirt.

Tilt to Purge Valve P/N 805-047

1. 

Cut tie wrap, and remove tilt-to-purge valve assembly.

2.  Push on the outside of the pod skirt to unseat the water dump valve 

body and valve. The two components will be removed as one unit inside 
the pod skirt. Do not attempt to push the valve body out through the 
tube of the pod skirt.

3.  Clean using a soft bristle brush and cleaning solution on the exterior 

surfaces of assembly. Place in ultrasonic cleaner using cleaning solution 
for 10 minutes. Re-clean with soft bristle brush if needed.

4.  Inspect component for damage. Replace if needed.

5.  Install the water dump valve 

body and valve back into the 
pod skirt as one unit. Verify cor-
rect orientation of the valve and 
seating into skirt tube.

NOTE

Valve orientation allows breathing gas and water to exit the pod 
when installed correctly.

6.  Install tilt-to-purge valve assembly so that the assembly is flush with 

tube end on rubber skirt of pod.

7.  Using tie wrap tool or equivalent, install new tie wrap P/N 520-038 to 

secure tilt-to- purge valve assembly in place on pod skirt. 

Содержание M-48 SuperMask

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды