manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, Руководство пользователя

Поделиться
Скачать
Kirby Morgan M-48 SuperMask Скачать руководство пользователя страница 37

Post Dive Procedures/Checklist

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

 

37

B

 

CAUTION

When not in use, component inlet/outlet ports shall be 
protected with clean, dry dust caps. Without this precau-
tion, contaminants and/or debris may enter the breathing 
system causing improper function.

Soft Pods and Mouthpiece Replacement Criteria

Prior to any dive visually inspect for any damage. Ensure all debris is cleared 
from pod before conducting inspection. The pod and/or mouthpiece should 
be replaced under the following conditions:

Visual inspection of both exterior and interior of pod reveals cuts, nicks, 
or general deterioration that could affect, fit, form or function. pod cover 
is cracked, torn, or punctured.

Connecting parts, such as pod catch, release or pod hook are not securely 
mounted or are damaged or worn, as described below:

pod catch, release does not make snapping sound while engaging the 
second and final ratchet tooth on pod Catch.

No sound or physical contact while engaging first ratchet tooth on mask 
hook (indicative of material fatigue).

Visual inspection of mouthpiece reveals cracks, tears, or general deterio-
ration.

REMEMBER:

 If any area of the pod, lenses, mask or mask strap fails, your 

MOUTHPIECE could be your LIFELINE! Make certain it is properly installed 
and in good condition.

Cleaning Procedures

After each day of diving, or between use by different users, the mask, and 
pod, should be carefully cleaned and visually inspected. Cleaning should be 
accomplished using a mild hand type dish washing soap and cleaning rag.

Mix the soap and water approximately one tablespoon per gallon of water. 
Wet all components of the mask and agitate using a cleaning rag. Keep the 
soap solution in contact with the mask surfaces for at least three to five 
minutes then thoroughly rinse with clean fresh water and dry. Clean and 
sanitize the demand regulator/BOV/DSV in accordance with the manufac-
turer’s recommendations.

The mask should be transported and stored, completely dried, in the stor-

Содержание M-48 SuperMask

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды