manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, Руководство пользователя

Поделиться
Скачать
Kirby Morgan M-48 SuperMask Скачать руководство пользователя страница 38

Post Dive Procedures/Checklist

38

 

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

age bag with the pod removed to keep the frame from taking a set. Follow 
the manufacturer’s recommendations on periodic maintenance of your 
demand regulator/BOV/DSV.

If the mask is equipped with communications, refer to the manufacturer’s 
post-dive procedures for proper corrective maintenance and care.

B

 

CAUTION

Clean and sanitize this mask using only the procedure 
described in this user’s guide. Never use cleaning sol-
vents or petroleum-based chemicals on this mask.

During a standard overhaul, parts should be cleaned in a warm water and 
mild soap solution, with a clean rag, and thoroughly rinsed in clean water. 
Hand dishwashing soap like Joy

®

, Dawn

®

 or Palmolive

®

 can be used.

With a solution of approximately one tablespoon of mild dish soap per 
gallon of warm water, a cleaning time of ten to fifteen minutes (parts 
submerged with some agitation with cleaning rag) is sufficient. Extended 
time should be avoided. A nylon toothbrush and/or tube brush can be 
used to remove corrosion. After cleaning, rinse all parts thoroughly with 
fresh water and allow drying. Always inspect the general condition of the 
pod and the components for any damage or wear before reassembling.

B

 

WARNING

Always sanitize all diving components an individual will 

be exposed to prior to use by another person. Failure to 

do so could result in the transmission of communicable 

diseases, some of which may cause long term disability 

or death.

B

 

CAUTION

Carefully dilute germicidal cleansing solutions in accor-
dance with manufacturers’ recommendation. If solution 
is not of the recommended strength, it will not act as an 
effective disinfectant.

Содержание M-48 SuperMask

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды