manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, Руководство пользователя

Поделиться
Скачать
Kirby Morgan M-48 SuperMask Скачать руководство пользователя страница 45

Accessories/Spares

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

 

45

Manifold Block

The M-48 SuperMask

®

 SCUBA pod can be 

used with surface supplied umbilical systems 
by using a manifold block system. The diver 
must be properly trained and equipped for 
surface supplied diving. A manifold block with 
a one way valve (non-return) that is securely 
fastened to a harness and bailout system must 
always be used when diving surface supplied.

The M-48 SuperMask

®

 is not equipped with a one-way valve (non-return) 

which is essential for surface supplied diving. This Manifold Block provides 
this essential system component. The Manifold Block Assembly shown 
comes in three configurations, P/N 300-150 with 9/16" Oxygen fitting, P/N 
300-155 with #6 JIC fitting or P/N 300-145 with standard SCUBA fitting. It 
is equipped with an Emergency Gas Supply valve, four low pressure outlets 
and a one-way valve (non-return).

Communications Port Plug P/N 820-155

If communications have been removed, the Communi-
cations Port Plug allows the mask to be used without 
communications.

Over-Pressure Relief Valve P/N 200-017

This valve is designed to be mounted on a first stage 
bail-out regulator for surface-supplied diving. It allows 
pressure to bleed from the intermediate pressure hose 
in the event of a “creeping” first stage. Without this 
valve, the intermediate pressure hose would burst and 
the diver would lose his entire emergency gas supply. 
(Torque specification for installing into low pressure 
port of first stage regulator: 20 inch pounds).

Содержание M-48 SuperMask

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды