manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, Руководство пользователя

Поделиться
Скачать
Kirby Morgan M-48 SuperMask Скачать руководство пользователя страница 35

Mask Clearing and Dewatering

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

 

35

tions through the nose 

before

 lifting the bottom of the mask frame and 

to 

continue exhaling until

 the frame returns to the face. 

The face forward position, increasing pressure (from exhaling) and purge 
assembly on the pod all work together to drain the water from both cavities 
of the mask.  When air bubbles are seen escaping from the dewatering/
purge valve, the pod has been cleared.

Review: Mask Clearing
1. 

Exhale through the nose (with mouthpiece in your mouth) or mouth 
closed.

2.  In a face forward position lift bottom of lens frame away from face

Mask Clearing with Tilt to Purge Assembly 

If using a pod fitted with the Tilt to Purge assembly this process is ac-
complished in the same manner as mentioned above, but will also require 
another hand to activate the tilt to purge valve. Pressing on the Valve Stem 
in any direction will active the valve.  When air bubbles are seen escaping 
from the dewatering/purge valve, the mask has been cleared.

Dewatering Basics

The same concept of clearing the mask applies to dewatering the pod. 
Increased pressure, by exhaling through the nose, is the force that pushes 
water through the water dump/ purge valve to clear the pod. When air 
bubbles are seen escaping from the valve, the mask has been cleared.

Hands Free

When using the SuperMask

®

 with the KMDSI Balanced SCUBA Regulator, 

dewatering the lower cavity is an effortless process that is hands free. The 
purge tube, located at the base of the pod Frame, houses a dewater/one-
way valve. This valve keeps water out and with an increase of cavity pres-
sure, by exhaling through the nose with the mouthpiece in your mouth or 
mouth closed, it allows water to be forced out of the lower section of the 
pod. Additional methods for dewater are also possible. Such as activating 
the purge on the regulator and having the mouth closed and mouthpiece 
out of the mouth.

Tilt to Purge 

When using a pod with a demand regulator other than the KMDSI Balanced 
SCUBA Regulator your hand will be required to activate the tilt to purge 
found at the base of the pod frame. 

Содержание M-48 SuperMask

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды