manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, Руководство пользователя

Поделиться
Скачать
Kirby Morgan M-48 SuperMask Скачать руководство пользователя страница 12

Diving Modes

12

 

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

NOTICE

The user cannot:

• remove the mark from the lens of the full face mask;

• modify or counterfeit the data reported on the mark.

NOTICE

The mark must be visible and legible throughout the life of 

the PPE. If the mark deteriorates or is not legible the user 

should contact the manufacturer.

Diving Modes

Using the M-48 SuperMask

®

 with Open Circuit SCUBA

For open circuit SCUBA, the M-48 SuperMask

®

 is used in much the same 

way as a half mask and standard second stage regulator. If you have pur-
chased the M-48 SuperMask

®

 with a SCUBA pod, the Mouthpiece P/N 

810-022L is included. Also note that if purchased with and mounted to 
the pod, is the new KMDSI Balance SCUBA second stage, the pod will 
be equipped with the automatic water purge system and NOT the tilt to 
purge valve assembly.

If your M-48 SuperMask

®

 and SCUBA pod P/N 805-015 are not already 

equipped with a Kirby Morgan second stage regulator, it is important that 
the regulator to be installed use only the Kirby Morgan P/N 810-022L 
mouthpiece. The instructions for mounting open circuit demand regula-
tors in this user guide must be read and understood before attempting to 
mount a second stage. When using this mask in countries that conform 
to CE standards the mask must only be used with components that have 
been CE certified. The maximum recommended recreational diving depth 
for the M-48 SuperMask

®

 with open circuit SCUBA is 130 FSW (39 msw) 

when operating under CE guidelines. 

Содержание M-48 SuperMask

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды