background image

MAINS PRESSURE HOT WATER STORAGE SYSTEM COMMISSIONING CHECKLIST

*

 All installations in England and Wales must be notified to Local Authority Building Control (LABC) either directly or through a Competent Persons Scheme.  
A Building Regulations Compliance Certificate will then be issued to the customer.  

©Heating and Hotwater Industry Council (HHIC)   

 

 

 

              www.centralheating.co.uk

ALL SYSTEMS PRIMARY SETTINGS

 (indirect heating only) 

Is the primary circuit a sealed or open vented system? 

Sealed 

  Open 

 

What is the maximum primary flow temperature? 

 

°C

ALL SYSTEMS 

What is the incoming static cold water pressure at the inlet to the system? 

 

bar

Has a strainer been cleaned of installation debris (if fitted)? 

Yes 

  No 

Is the installation in a hard water area (above 200ppm)? 

Yes 

  No 

If yes, has a water scale reducer been fitted? 

Yes 

  No 

What type of scale reducer has been fitted? 

What is the hot water thermostat set temperature? 

 

°C

What is the maximum hot water flow rate at set thermostat temperature (measured at high flow outlet)? 

  

l/min

Time and temperature controls have been fitted in compliance with Part L of the Building Regulations? 

 

Yes 

 

Type of control system (if applicable) 

Y Plan 

 

S Plan 

 

Other 

 

Is the cylinder solar (or other renewable) compatible? 

Yes 

  No 

What is the hot water temperature at the nearest outlet? 

 

°C

All appropriate pipes have been insulated up to 1 metre or the point where they become concealed 

 

Yes 

 

UNVENTED SYSTEMS ONLY 

Where is the pressure reducing valve situated (if fitted)?

What is the pressure reducing valve setting?  

 

bar

Has a combined temperature and pressure relief valve and expansion valve been fitted and discharge tested? 

Yes 

  No 

The tundish and discharge pipework have been connected and terminated to Part G of the Building Regulations 

 

Yes 

Are all energy sources fitted with a cut out device? 

Yes 

  No 

Has the expansion vessel or internal air space been checked? 

Yes 

  No 

THERMAL STORES ONLY 

What store temperature is achievable? 

 

°C

What is the maximum hot water temperature? 

 

°C

ALL INSTALLATIONS 

 

The hot water system complies with the appropriate Building Regulations 

Yes 

 

The system has been installed and commissioned in accordance with the manufacturer’s instructions 

Yes 

 

The system controls have been demonstrated to and understood by the customer 

Yes 

 

The manufacturer’s literature, including Benchmark Checklist and Service Record, has been explained and left with the customer 

Yes 

 

Commissioning Engineer’s Signature

Customer’s Signature

(To confirm satisfactory demonstration and receipt of manufacturer’s literature)

This Commissioning Checklist is to be completed in full by the competent person who commissioned the storage system as a means of 
demonstrating compliance with the appropriate Building Regulations and then handed to the customer to keep for future reference.  

Failure to install and commission this equipment to the manufacturer’s instructions may invalidate the warranty but does not affect statutory rights.      

Customer Name  

Telephone Number

Address 

Cylinder Make and Model 

Cylinder Serial Number 

Commissioned by 

(print name)

 

Registered Operative ID Number

Company Name 

Telephone Number

Company Address

 

 

Commissioning Date 

To be completed by the customer on receipt of a Building Regulations Compliance Certificate

*

:

Building Regulations Notification Number 

(if applicable)

Содержание AUXD120





























Отзывы: