background image

Benchmark places responsibilities on both manufacturers and installers. 
The purpose is to ensure that customers are provided with the correct 
equipment for their needs, that it is installed, commissioned and serviced 
in accordance with the manufacturer’s instructions by competent 
persons and that it meets the requirements of the appropriate Building 
Regulations. The Benchmark Checklist can be used to demonstrate 
compliance with Building Regulations and should be provided to the 
customer for future reference.  

Installers are required to carry out installation, commissioning and 
servicing work in accordance with the Benchmark Code of Practice which 
is available from the Heating and Hotwater Industry Council who manage 
and promote the Scheme. Visit www.centralheating.co.uk  for more 
information.

SERVICING

H2

GENERAL

Servicing should only be carried out by competent installers 
and any spare parts used must be purchased from Kingspan 
Environmental. NEVER bypass any safety devices or operate 
the unit without them being fully operational.

DRAINING

Isolate from the electrical supply to prevent the immersion 
heaters burning out. Turn off the boiler. Isolate the unit from 
the cold mains. Attach a hose to the draining tap ensuring that 
it reaches to a level below the unit (this will ensure an efficient 
syphon is set up and the maximum amount of water is drained 
from the unit). First open the hot tap closest to the unit and 
then open the draining tap. 

WARNING: WATER DRAINED OFF MAY BE VERY HOT!

IMPORTANT: After draining the cylinder do not close the hot 
tap until the cylinder has fully cooled, failure to follow this 
instruction may result in damage to the cylinder and will 
invalidate the guarantee.

ANNUAL MAINTENANCE

ULTRASTEEL PLUS requires an annual service in order to 
ensure safe working and optimum performance. It is essential 
that the following checks are performed by a competent 
installer on an annual basis. Commonly this is done at the 
same time as the annual boiler service.
An annual service should include the following as a minimum

1. Recharging of the expansion volume
2. Checking of all safety valves to ensure they are not leaking
and function correctly
3. Testing of thermostats to ensure they are functioning
correctly
4. Cleaning of filter on inlet control set
5. Test immersionn heater for continuity and resistance
6.  Record temperature of hot water at outlet after 1 minute of 
flow
7. Ensure discharge pipe discharges fully
8. Complete Benchmark Service record

KINGSPAN ALBION
RELIABLE HOT WATER CYLINDERS

Содержание AUXD120





























Отзывы: