Kikusui KJM6710 Скачать руководство пользователя страница 54

Страница: 54 / 60

6-2 Specifications

KJM6710

Trigger section

Equalizer section

The equalizer characteristics are obtained by converting the charac-
teristics given in the DVD BOOK to a 27-MHz reference clock.

PLL clock regeneration section

Frequency response characteristics are valid for reference clock = 27 MHz.

Complies with DVD Speci

cations for Read-Only Disc Ver.1.0 Aug 1996.

Symmetry follow-up

AUTO, AUTO+ OFFSET, or MANUAL

Trigger edge

Rising edge, falling edge, or both

CLOCK

Rising edge or falling edge

Delay

Adjust the phase difference with the RF
signal by delaying the CLOCK signal

AUTO or MANUAL switchable

MANUAL adjustment range 0

to 360

Frequency characteristics

5.16 MHz: +3.2

0.3 dB

(Amplitude ratio with respect to 10 kHz)

10.3 MHz: –2.8

1.0 dB

(Amplitude ratio with respect to 10 kHz)

Group delay characteristics

Maximum group delay deviation

≤

6 ns

(Frequency range: 0.7 MHz

≤

6.7 MHz)

Synchronizable signal

8-16 modulation signal that corresponds
to a fundamental frequency of 25 MHz
to 30 MHz.

Frequency response characteristics
(100 Hz reference, closed-loop charac-
teristics)

1 kHz: 0.2

1.7 dB

3 kHz: 1.3

1.7 dB

7 kHz: 1.0

1.7 dB

15 kHz: –4.0

1.7 dB

Lockup time

Within 700 ms

Synchronizable jitter range

5 % to 17 %

Residual jitter

2 % or less

Содержание KJM6710





























































Результаты поиска

Содержание KJM6710

Отзывы:

Kikusui KJM6710, Руководство по эксплуатации, Страница: 54 / 60

Результаты поиска

Содержание KJM6710

Отзывы: