Kikusui KJM6710 Скачать руководство пользователя страница 25

Страница: 25 / 60

KJM6710

Operation 3-7

3.2

Function Setup

There are two methods for setting the internal functions of the

KJM6710.

1. By using the function setup switches on the rear panel.
2. By transmitting messages via the RS-232C interface.

The table below shows the possible combinations of the setup

through the function setup switches.

Do not turn both RF EDGE switches to

(ON).

After setting the switches, DELAY which is not indicated in the table is

set to AUTO, and SYMMETRY LEVEL (when set to SYMMETRY

MANUAL) is set to 0 V.
The BPS (baud rate) switch setting takes effect the next time the

KJM6710 is powered up. Other switch settings take effect immediately.
All settings except the BPS (baud rate) setting can be con

gured

using RS-232C command messages. The settings that actually take

effect are those speci

ed last.

Operation when set to

(OFF)

Operation when set to

(ON)

BPS (baud rate)

200 BPS

600 BPS

OFF

PLL

OFF

TIME CONST

0.1 s

1 s

SYMMETRY

AUTO

MANUAL (0 V)

CLOCK EDGE

positive

negative

RF EDGE

positive

either

negative

Содержание KJM6710





























































Результаты поиска

Содержание KJM6710

Отзывы:

Kikusui KJM6710, Руководство по эксплуатации, Страница: 25 / 60

Результаты поиска

Содержание KJM6710

Отзывы: