Kikusui KJM6710 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 60

Kikusui KJM6710 Скачать руководство пользователя страница 35

KJM6710

RS-232C Control 4-3

4.3

Device Messages

Device messages refer to program messages and response messages

that the KJM6710 supports.
This section describes the device messages one by one.
Program messages are not case-sensitive. Response messages are

returned in upper-case.

Abbreviated form

Abbreviations are provided for program messages and some of the

character program data.
The device message inside the parentheses is the abbreviated form of

the device message name.

• Response messages are returned in the abbreviated form.

Special symbols and characters

Special symbols and characters used in this manual to describe pro-
gram messages and response messages are de

fi

ned as shown in Table

Table 4-1 De

fi

nitions of special symbols and characters

Symbol and Character

Description

< >

Denotes program data.
Do not include the enclosing characters in the
actual program.

{ }

Characters and numbers delimited by “|” in
braces indicate that one of the items is to be
selected.
Do not include the enclosing characters in the
actual program.

_

Denotes a space.

«
...
33
34
35
36
37
...
»

Содержание KJM6710





























































Отзывы:

Нет отзывов