Kikusui KJM6710 Скачать руководство пользователя страница 14

Страница: 14 / 60

1-2 Setup

KJM6710

1.2

Installation

How to install the KJM6710

■

The KJM6710 is designed for embedded application

and provides attachment screw holes on the side

and bottom panels. To

x the KJM6710 in place, use

these screw holes. If you are not

xing the KJM6710

in place, attach the stand provided to the bottom

panel and place the KJM6710 so that it stands up.
Secure adequate space around the KJM6710 so

that air can circulate around it.

Precautions concerning installation location

This section describes the precautions to be taken when installing the

KJM6710. Make sure to observe them.

■

Do not use the KJM6710 in a

ammable atmosphere.

To prevent the possibility of explosion or

re, do not use the

KJM6710 near alcohol, thinner or other combustible materials, or in

an atmosphere containing such vapors.

■

Avoid locations where the KJM6710 is exposed to

high temperature or direct sunlight.

Do not place the KJM6710 near a heater or in areas subject to drastic

temperature changes.
Operating temperature range:

C to 40

Spec guaranteed temperature range: 15

C to 35

Storage temperature range:

-20

C to 60

30 mm or more

30 mm

or more

30 mm

or more

30 mm

or more

[When using the stand]

Содержание KJM6710





























































Результаты поиска

Содержание KJM6710

Отзывы:

Kikusui KJM6710, Руководство по эксплуатации, Страница: 14 / 60

Результаты поиска

Содержание KJM6710

Отзывы: