Kikusui KJM6710 Скачать руководство пользователя страница 50

Страница: 50 / 60

5-2 Maintenance

KJM6710

5.4

Troubleshooting

The symptoms listed below may not necessarily mean a malfunction.

Check the KJM6710 before requesting repairs.
If the remedy does not solve the problem or if your case does not

match any of the items, contact your Kikusui agent.

Table 5-1

Symptom

Check Items

Description

The KJM6710
does not oper-
ate even when
the power
switch is
turned on.

Is the line voltage
correct?

The allowable line voltage range is
14.5 V to 15.5 V. The line voltage may
drop if the power supply capacity is
insuf

cient.

Is the DC voltage polarity
correct?

For safety reasons, the fuse is
designed to blow when the DC voltage
polarity is reversed. If the fuse is
blown, request for repairs.

Cannot make
measurements.

Is the input amplitude
adequate?

The input impedance must be 50

Ω

and the input amplitude must be at
least 0.2 Vp-p. 1-M

Ω

probes cannot

be used.

Is the output impedance
correct?

Check that the output impedance of
the connected device and the cable
impedance are 50

Ω

Is the duty cycle of clock
signal outside the speci

cations?

The duty cycle speci

cation of the

clock signal is 45:55 to 50:50.

PLL does not
lock.

If the frequency correct?

The PLL of the KJM6710 can lock to
fundamental clock frequencies
between 25 MHz to 30 MHz.

Is the amount of jitter too
large?

The PLL of the KJM6710 can lock up
to 17 %.

Содержание KJM6710





























































Результаты поиска

Содержание KJM6710

Отзывы:

Kikusui KJM6710, Руководство по эксплуатации, Страница: 50 / 60

Результаты поиска

Содержание KJM6710

Отзывы: