Kikusui KJM6710 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 60

Kikusui KJM6710 Скачать руководство пользователя страница 15

KJM6710

Setup 1-3

■

Avoid humid environments.

Do not place the KJM6710 in high-humidity locations--near a boiler,

humidi

fi

er, or water supply.

Operating humidity range: 20 % to 85 % RH (no condensation)
Storage humidity range:

0 to 90 % RH (no condensation)

Condensation may occur even within the operating humidity range.

In such cases, do not use the KJM6710 until the condensation dries

up completely.

■

Do not place the KJM6710 in a corrosive atmosphere.

Do not install the KJM6710 in a corrosive atmosphere or in environ-
ments containing sulfuric acid mist, etc. This may cause corrosion of

various conductors and bad contacts of connectors inside the

KJM6710 leading to malfunction and failure, or in the worst case, a

fi

re.

■

Do not place the KJM6710 in a dusty location.

Accumulation of dust can lead to electric shock or

fi

re.

■

Do not place the KJM6710 on an inclined surface

or location subject to vibrations.

The KJM6710 may fall or tip over causing damages and injuries.

■

Do not use the KJM6710 in a location subject to

strong magnetic or electric

fi

elds.

The KJM6710 may malfunction and cause electric shock or

fi

re.

■

Do not place objects on top of the KJM6710.

Placing objects on top of the KJM6710 can cause failures (especially

heavy objects).

«
...
13
14
15
16
17
...
»

Содержание KJM6710





























































Отзывы:

Нет отзывов