Keysight U8001A Скачать руководство пользователя

Страница: 24 / 81

General Information

Keysight U8001A/U8002A User’s and Service Guide

Display Annunciators

Constant Current

OFF

Constant Voltage

Memory State 1

Memory State 2

Memory State 3

Over voltage Protection

Over current Protection

Limit

LOCK

Annunciators

Functions

Stores states of power supply in non-volatile memory.
When the power supply is in calibration mode, it can be used to store calibration constant.

OVP

The over voltage protection function is enabled when the annunciator turns on or the over voltage

protection circuit has caused the power supply to shutdown when the annunciator blinks.

OCP

The over current protection function is enabled when the annunciator turns on or the over current

protection circuit has caused the power supply to shutdown when the annunciator blinks.

LOCK

The front panel operation is disabled.

LIMIT

The display shows the limit values of voltage and current.

OFF

The output of the power supply is disabled.

The power supply is in constant voltage mode when the annunciator blinks.

The power supply is in constant current mode when the annuciator blinks.

Содержание U8001A


















































































Результаты поиска

Содержание U8001A

Отзывы:

Похожие инструкции для U8001A

Бренды по названию

Популярные бренды

Keysight U8001A, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U8001A

Отзывы:

Похожие инструкции для U8001A

Бренды по названию

Популярные бренды