Keysight U8001A Скачать руководство пользователя

Страница: 57 / 81

Service Guide

Keysight U8001A/U8002A User’s and Service Guide

Performance Verification and Calibration

This chapter contains performance verification and calibration procedures. The

performance verification procedures allow you to verify that the power supply is

operating within its published specifications. The calibration procedures show

how to make voltage and current adjustment on the power supply.

Keysight Technologies calibration services

When your instrument is due for calibration, contact your local Keysight Service

Center for a low-cost recalibration.

Calibration interval

One year interval is recommended for most applications. Accuracy specifications

are warranted only if calibration is made at regular calibration interval. Accuracy

specifications are not warranted beyond the one year calibration interval. Keysight

does not recommend extending calibration intervals beyond two years for any

application. Keysight recommends that complete re-adjustment should always be

performed at the calibration interval. This will increase your confidence that the

U8001A and U8002A will remain within specification for the next calibration

interval. The re-adjustment provides the best long-term stability and accuracy.

Содержание U8001A


















































































Результаты поиска

Содержание U8001A

Отзывы:

Похожие инструкции для U8001A

Бренды по названию

Популярные бренды

Keysight U8001A, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U8001A

Отзывы:

Похожие инструкции для U8001A

Бренды по названию

Популярные бренды