Keysight U8001A Скачать руководство пользователя

Страница: 32 / 81

Operations and Features

Keysight U8001A/U8002A User’s and Service Guide

Constant Voltage Operation

The following steps show you how to perform the constant voltage (CV)

operation.

1 Turn on the power supply.

– Press on the “Power” button to turn on the power supply. The power supply

will then perform a self-test (Self-test is not indicated at display).

– The display turns on all segments and shows the firmware version briefly

after that.

– The output is disabled by default.
– The OFF annunciator turns on.
– The display shows “OFF”

2 Set the display to the limit mode.

– Press on the “Display Limit” button in order to turn on the LIMIT

annunciator.

– The display will show the voltage and current limit values.

3 Ad just for the desired output voltage.

– Press on the “Voltage/Current” button. When seeing the voltage value, “V”

blinks, turn the knob to adjust for the desired output voltage value.

NOTE

When you press on the Display Limit button, the voltage and current limit values

will be shown on the display for about five seconds. If there is no activity

detected, the display will return to meter view mode.

Содержание U8001A


















































































Результаты поиска

Содержание U8001A

Отзывы:

Похожие инструкции для U8001A

Бренды по названию

Популярные бренды

Keysight U8001A, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U8001A

Отзывы:

Похожие инструкции для U8001A

Бренды по названию

Популярные бренды