Keysight U8001A Скачать руководство пользователя

Страница: 6 / 81

Keysight U8001A/U8002A User’s and Service Guide

Regulatory Markings

The CE mark is a registered trademark

of the European Community. This CE

mark shows that the product complies

with all the relevant European Legal

Directives.

The RCM mark is a registered

trademark of the Australian

Communications and Media Authority.

ICES/NMB-001 indicates that this ISM

device complies with Canadian

ICES-001.

This instrument complies with the

WEEE Directive (2002/96/EC) marking

requirement. This affixed product label

indicates that you must not discard

this electrical/electronic product in

domestic household waste.

The CSA mark is a registered

trademark of the Canadian Standards

Association. A CSA mark indicates that

the product is certified for Canadian

markets, to the applicable Canadian

standards.

Содержание U8001A


















































































Результаты поиска

Содержание U8001A

Отзывы:

Похожие инструкции для U8001A

Бренды по названию

Популярные бренды

Keysight U8001A, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U8001A

Отзывы:

Похожие инструкции для U8001A

Бренды по названию

Популярные бренды