Keysight U8001A Скачать руководство пользователя

Страница: 35 / 81

Operations and Features

Keysight U8001A/U8002A User’s and Service Guide

5 Adjust for the desired output current.

– Press on the “Voltage/Current” button. When seeing the current value, “A”

blinks, turn the knob to adjust for the desired output current value.

6 Return to the meter mode.

– Press on the “Display Limit” button to return to the meter mode. The LIMIT

annunciator will be turned off.

7 Enable the output.

– Press on the “Output On/Off” button to enable the output.
– The OFF annunciator turns off and constant current (CC) annunciator turns

on.

– The display is now in meter mode.

NOTE

Verify that the power supply is in constant current mode. Ensure that the

constant current (CC) annunciator is on. If the constant voltage (CV) annunciator

is on instead, choose a higher voltage limit.

Содержание U8001A


















































































Результаты поиска

Содержание U8001A

Отзывы:

Похожие инструкции для U8001A

Бренды по названию

Популярные бренды

Keysight U8001A, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U8001A

Отзывы:

Похожие инструкции для U8001A

Бренды по названию

Популярные бренды