Keysight U8001A Скачать руководство пользователя

Страница: 38 / 81

Operations and Features

Keysight U8001A/U8002A User’s and Service Guide

Programming Over Voltage Protection

Over voltage protection guards the load against output voltages reaching values

greater than the programmed protection level.
The following steps show how to enable and disable the over voltage protection

(OVP), how to set the OVP trip level and how to clear the over voltage condition.

To set the OVP trip level and enable OVP

1 Press on the “Over Voltage” button.

– The LIMIT annunciator will be turned off.
– The OVP annunciator will fast-blink continuously.
– The display will show the OVP value and the character “V” will fast-blink

continuously.

2 Turn the knob to adjust the OVP value.

3 Press on the “Over Voltage” button again to end the adjustment and enable

the OVP.

– Display will show “donE”.
– The OVP annunciator will be turned on.

NOTE

To cancel the operation, allow the unit to idle for five seconds.

Содержание U8001A


















































































Результаты поиска

Содержание U8001A

Отзывы:

Похожие инструкции для U8001A

Бренды по названию

Популярные бренды

Keysight U8001A, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U8001A

Отзывы:

Похожие инструкции для U8001A

Бренды по названию

Популярные бренды