Keysight U8001A Скачать руководство пользователя

Страница: 19 / 81

Quick Start

Keysight U8001A/U8002A User’s and Service Guide

If the Power Supply Does Not Turn On

Use the following steps to help solve problems you might encounter when turning

on the instrument. If you need more help, refer to

Chapter 5

for instructions on

returning the instrument to Keysight Technologies for service.

1 Verify that there is AC power to the power supply.

First, verify that the power cord is firmly plugged into the power receptacle on

the rear panel of the power supply. You should also make sure that the power

source you plugged the power supply into is energized. Then, verify that the

power supply is turned on.

2 Verify the power-line voltage setting.

The line voltage is set to the proper value for your country when the power

supply is shipped from the factory. Change the voltage setting if it’s not

correct. The settings are: 100, 115, or 230 Vac.

3 Verify that the correct power-line fuse is installed.

The correct fuse is installed for your country when the power supply is shipped

from the factory. See the table below to replace the fuse for your power supply.

Table 1-1

List of rated fuse for line voltages

Model

Part number

Part description

U8001A

2110-0014
2110-0006

Fuse 4.0 A T for 100 and 115 Vac
Fuse 2.0 A T for 230 Vac

U8002A

2110-0722
2110-1425

Fuse 6.25 A T for 100 and 115 Vac
Fuse 2.8 A T for 230 Vac

Содержание U8001A


















































































Результаты поиска

Содержание U8001A

Отзывы:

Похожие инструкции для U8001A

Бренды по названию

Популярные бренды

Keysight U8001A, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U8001A

Отзывы:

Похожие инструкции для U8001A

Бренды по названию

Популярные бренды