Keysight MIPI M-PHY Скачать руководство пользователя страница 66

Страница: 66 / 76

Keysight MIPI M-PHY Frame Generator User Guide

Using the Software

Wildcards

If a sequence name contains one or more wildcards, the name of the

sequence that is actually running changes as the wildcards are replaced

by particular values during the run time, depending on the test specifics.

Table 3

lists the names of the wildcards that are supported for sequence

names, along with their possible values. No wildcards are mandatory.

Table 3

Supported wildcards for sequence names and their possible values

Wildcard

Values

Tab in which the value of the wildcard can be
changed

[HsGear]

Gear1A, …, Gear5B

Data Rates Tab

[Mode]

Cont, Burst

Protocol Tab

[Amplitude]

Large, Small

Protocol Tab

[Channel]

Data0, DataAll

For Rx Test Mode (UniPro Script Generator):
Protocol Tab;
For Tx Test Mode (UniPro Script Generator):
Pattern Tab

Содержание MIPI M-PHY













































































Результаты поиска

Содержание MIPI M-PHY

Отзывы:

Похожие инструкции для MIPI M-PHY

Бренды по названию

Популярные бренды

Keysight MIPI M-PHY, Руководство пользователя

Результаты поиска

Содержание MIPI M-PHY

Отзывы:

Похожие инструкции для MIPI M-PHY

Бренды по названию

Популярные бренды