Keysight MIPI M-PHY Скачать руководство пользователя страница 36

Страница: 36 / 76

Keysight MIPI M-PHY Frame Generator User Guide

Using the Software

Parameters in the Protocol Tab

High Speed Timing Settings

•

HS Prepare Length [SI]

: PREPARE is the initial sub-state before the

HS-burst starts and HS Prepare Length defines the number of DIFP

(Differential Positive Voltage) states before the bit stream is started.

The actual HS Prepare Length can be calculated with the formulas

given in

Table 7 “PREPARE, SYNC, and ADAPT Attribute and Dependent

Parameter Values” of the MIPI

Alliance Specification for M-PHY

Version 5.0 document

•

Stall Length [UI]

: This defines the number of DIFN (Differential

Negative Voltage) states after a data burst. This parameter only affects

the data output when the sequence file (see

Pattern Tab

on page 40)

contains a “STALL” entry in the data block definition.

•

HS Sync Length [SI]

: This defines the number of SYNC pattern symbols

before the burst starts. For HS mode, the Prepare Length will be

followed by a SYNC sequence (D10.5, D26.5). In HS burst and PWM

burst modes, the SYNC sequence is followed by the payload. The

payload starts with MARKER0 (MK0)

•

HS Sync Length [SI]

: This defines the number of SYNC pattern symbols

before the burst starts. For HS mode, the Prepare Length will be

followed by a SYNC sequence (D10.5, D26.5). In HS burst and PWM

burst modes, the SYNC sequence is followed by the payload. The

payload starts with MARKER0 (MK0).

•

HS Sync Range

: Select either

Fine

Coarse

for the HS Sync Range.

For Fine, the duration of the HS sync sequence T

SYNC

is equal to the HS

Sync Length: T

SYNC

= SYNC_length.

For Coarse, T

SYNC

= min(2

SYNC_length

, 2

For more details see

Table 7 “PREPARE, SYNC, and ADAPT Attribute

and Dependent Parameter Values” of the MIPI

Alliance Specification

for M-PHY

Version 5.0 document and the text just before that table.

•

Initial Adapt Length

: The ADAPT sub-state is intended to allow the

DUT equalizer training to adapt to the channel characteristic when

receiving an HS data stream. The ADAPT sequence starts with a MK0

followed by an 8b10b-encoded PRBS9 pattern completed by one b0

bit. The Initial Adapt Length parameter defines the duration of the

Initial ADAPT sequence after power-up.

•

Refresh Adapt Length

: This defines the duration of the refresh ADAPT

sequence during link operation.

•

Initial Adapt Type

: Select either

Fine

Coarse

For Fine, the duration of the Initial ADAPT sequence is calculated as

ADAPT

= 650 * (ADAPT_ 1).

For Coarse, T

ADAPT

= 650 * 2

ADAPT_length

, where ADAPT_length < 18.

Содержание MIPI M-PHY













































































Результаты поиска

Содержание MIPI M-PHY

Отзывы:

Похожие инструкции для MIPI M-PHY

Бренды по названию

Популярные бренды

Keysight MIPI M-PHY, Руководство пользователя

Результаты поиска

Содержание MIPI M-PHY

Отзывы:

Похожие инструкции для MIPI M-PHY

Бренды по названию

Популярные бренды