Keysight MIPI M-PHY Скачать руководство пользователя страница 63

Страница: 63 / 76

Keysight MIPI M-PHY Frame Generator User Guide

Using the Software

•

Tx Length Parameters

•

HS Sync Length

: Read-only value of the length of the HS Sync

Sequence that results from the selected values of Coarse and Fine.

It is the number of Sync Sequence Symbols before the burst starts.

See

HS Sync Range

•

Coarse

: Parameter to change the length of the HS Sync Sequence.

Min: 0

Default: 1

Max: 1

•

Fine

: Parameter to change the length of the HS Sync Sequence.

Min: 0

Default: 15

Max: 15

•

HS Prepare Length

: This defines the number of DIFP states before the

bit stream starts. That is, the parameter sets the length of the HS

Prepare state.

Min: 0

Default: 15

Max: 15

•

LS Prepare Length

: This defines the number of DIFP states before a

PWM Burst. That is, the parameter sets the length of the LS Prepare

state.

Min: 0

Default: 15

Max: 15

•

STALL Time

: This defines the number of DIFN states after a HS data

burst. That is, the parameter sets the length of the power-saving Stall

state between HS bursts.

•

Custom Packets

: This enables you to change the default values of the

registers used in the default script. For example, in a particular custom

packet, you could enter the address 0x80F9 in the address field and the

value 0x01 in the value field. After the script has been generated, the

value of 0x01 will be used for the register 0x80F9 instead of the default

value 0x00.

Sequence Parameters

•

Gap Length

: The parameters in this section are used to specify the

lengths of the different gaps that are used in the training sequence.

•

Gap Unit

: The default unit is Symbols.

Содержание MIPI M-PHY













































































Результаты поиска

Содержание MIPI M-PHY

Отзывы:

Похожие инструкции для MIPI M-PHY

Бренды по названию

Популярные бренды

Keysight MIPI M-PHY, Руководство пользователя

Результаты поиска

Содержание MIPI M-PHY

Отзывы:

Похожие инструкции для MIPI M-PHY

Бренды по названию

Популярные бренды