Keysight MIPI M-PHY Скачать руководство пользователя страница 6

Страница: 6 / 76

Keysight MIPI M-PHY Frame Generator User Guide

Introduction

Overview

The MIPI

M-PHY Frame Generator software (for short “Frame Generator”

or “software”) is a stand-alone software utility. It provides semi-automatic

control of Keysight Technologies M8040A J-BERT (Jitter Bit Error Ratio

Tester) based MIPI

M-PHY generator hardware for physical layer tests.

For UniPro and UFS testing, the BERT equipment can be combined with

the BIT-3000 DSGA to put the DUT into UniPro Test Mode and retrieve the

Frame and Error Counters.

The Frame Generator is a flexible tool for trouble-shooting and debugging.

It complements the full Test Automation Software, which provides

automated physical layer compliance tests and device characterization.

The Frame Generator generates the data sequences and allows pattern

changes as well as the control of signal levels, data rate, and timing

parameters.

The software runs on a standard Windows PC and controls the hardware

test resources through appropriate interfaces such as LAN.

NOTE

The definitions of the acronyms and abbreviations used throughout this

User Guide are given in

“Appendix A: Acronyms and Abbreviations”

Содержание MIPI M-PHY













































































Результаты поиска

Содержание MIPI M-PHY

Отзывы:

Похожие инструкции для MIPI M-PHY

Бренды по названию

Популярные бренды

Keysight MIPI M-PHY, Руководство пользователя

Результаты поиска

Содержание MIPI M-PHY

Отзывы:

Похожие инструкции для MIPI M-PHY

Бренды по названию

Популярные бренды