Keysight Technologies N774 C Series Скачать руководство пользователя

Страница: 31 / 84

Keysight N774xC Series Multiport Power Meter User’s Guide

Getting Started

LAN Interface

The LAN LED

When the LAN connection is made, you will see the following indicators:

There may be a delay between making the LAN link (yellow status) and

getting the IP address (green status). This delay may be longer if there is

no DHCP server, for example when the instrument is connected directly to

a PC.

The LAN Reset button

This recessed button has two functions.
• Pressing the button briefly invokes a preset of the instrument and

restores default measurement settings. This is equivalent to the

programming command:

:SYSTem:PRESet

• Pressing and holding the button for 5 seconds will reset the LAN

parameters to the factory default. This includes removing the password.

This is equivalent to the following programming command:

:SYSTem:COMMunicate:ETHernet:RESet

Red

LAN

No LAN link

Yellow

LAN

Green

LAN

No IP Address

LAN link

Содержание N774 C Series





















































































Результаты поиска

Содержание N774 C Series

Отзывы:

Похожие инструкции для N774 C Series

Бренды по названию

Популярные бренды

Keysight Technologies N774 C Series, Руководство пользователя

Результаты поиска

Содержание N774 C Series

Отзывы:

Похожие инструкции для N774 C Series

Бренды по названию

Популярные бренды