Keysight Technologies N774 C Series Скачать руководство пользователя страница 73

Страница: 73 / 84

Keysight N774xC Series Multiport Power Meter User’s Guide

User Interface Reference

2 Enter the descriptions for the following LAN configuration parameters:

•

Instrument identification

•

IP address configuration

•

DNS server address configuration

Once, the changes are done, click on

Apply Changes

button.

WARNING

Your connection to the instrument may be broken after executing either

of the operations below. If so, reconnect to the instrument using the new

hostname or IP address.

NOTE

For IP address and DNS server configuration, you can select the Use

Automatic Configuration check-box to automatically select the

IP address and DNS server.

NOTE

It can take up to 30 seconds for changes to these settings to take effect.

You may need to refresh the Configure LAN page after 30 seconds to see

the updated settings. Changes in hostname and description require

reboot or LAN restart to take effect.

Содержание N774 C Series





















































































Результаты поиска

Содержание N774 C Series

Отзывы:

Похожие инструкции для N774 C Series

Бренды по названию

Популярные бренды

Keysight Technologies N774 C Series, Руководство пользователя

Результаты поиска

Содержание N774 C Series

Отзывы:

Похожие инструкции для N774 C Series

Бренды по названию

Популярные бренды