Keysight Technologies N774 C Series Скачать руководство пользователя

Страница: 28 / 84

Keysight N774xC Series Multiport Power Meter User’s Guide

Getting Started

Optical Connections

The N774xC power meters do not make contact to the fiber connector

faces and can be used with either angled or straight polished connectors.

The N7744C and N7745C use the quad-adapters described below.

Making Quad-adapter Connections on the Keysight N7744/45C Multiport
Power Meters

Figure 8

Making Quad-Adapter Connection

CAUTION

When using bare fiber connections to power meters, the length of fiber

extending from the fiber holder must be carefully adjusted to avoid

scratching the power meter optics.

Optical Inputs

Quad Adapter

Optical Connectors

NOTE

Before you attach a quad-adapter or fiber, you should make sure they are

clean. This is important for accurate measurements. The fibers do not

contact the optical inputs (all contact with the optical inputs should be

avoided). Usually the only cleaning necessary for the optical inputs is the

gentle removal of dust with pressurized, dry air.
For further information, refer to “Maintenance” section, described in this

N774xC User’s Guide

Содержание N774 C Series





















































































Результаты поиска

Содержание N774 C Series

Отзывы:

Похожие инструкции для N774 C Series

Бренды по названию

Популярные бренды

Keysight Technologies N774 C Series, Руководство пользователя

Результаты поиска

Содержание N774 C Series

Отзывы:

Похожие инструкции для N774 C Series

Бренды по названию

Популярные бренды