Keysight Technologies N774 C Series Скачать руководство пользователя

Страница: 41 / 84

Keysight N774xC Series Multiport Power Meter User’s Guide

Definition of Terms

This section defines terms that are used in this document.

Specification

Describes warranted product performance that is valid under the specified

conditions. Specifications include guard bands to account for the expected

statistical performance distribution, measurement uncertainties, changes

in performance due to environmental changes and aging of components.

Typical Value (Characteristics)

Characteristics describe the product performance that is usually met but

not guaranteed. Typical values are based on data from a representative set

of instruments.

Generally, all specifications are valid within the specified temperature

range, after warm-up, at the stated operating conditions and

measurement settings.

Operating Conditions

The environmental conditions for system operation. The system must not

be operated outside these conditions.

Specified Temperature

The temperature range where the specifications apply (if not differently

stated).

Ambient Temperature Range

Temperature range of the ambient environment where specifications

apply.

(Applicable) fiber type

Connection type for which the specifications and characteristics apply

(if not differently stated).

Содержание N774 C Series





















































































Результаты поиска

Содержание N774 C Series

Отзывы:

Похожие инструкции для N774 C Series

Бренды по названию

Популярные бренды

Keysight Technologies N774 C Series, Руководство пользователя

Результаты поиска

Содержание N774 C Series

Отзывы:

Похожие инструкции для N774 C Series

Бренды по названию

Популярные бренды