Keysight Technologies N774 C Series Скачать руководство пользователя

Страница: 77 / 84

Keysight N774xC Series Multiport Power Meter User’s Guide

Maintenance

Before you make any connection you must ensure that all cables and

connectors are clean. If they are dirty, use the appropriate cleaning

procedure.

When inserting the ferrule of a patchcord into a connector or an adapter,

make sure that the fiber end does not touch the outside of the mating

connector or adapter. Otherwise you will rub the fiber end against an

unsuitable surface, producing scratches and dirt deposits on the surface of

your fiber.

What materials do I need for proper cleaning?

Following are some standard cleaning equipment necessary for cleaning

your instrument:

Standard Cleaning Equipment

Before you can start your cleaning procedure you need the following

standard equipment:
• Dust and shutter caps
• Isopropyl  alcohol
• Cotton  swabs
• Soft tissues
• Compressed  air

Dust and shutter caps

All of Keysight Technologies’ lightwave instruments are delivered with

either laser shutter caps or dust caps on the lightwave adapter. All cables

come with covers to protect the cable ends from damage or

contamination.

We suggest these protected coverings should be kept on the equipment at

all times, except when your optical device is in use. Be careful when

reattaching dust caps after use. Do not press the bottom of the cap onto

the fiber too hard, as any dust in the cap can scratch or pollute your fiber

surface.

Isopropyl alcohol

This solvent is usually available from any local pharmaceutical supplier or

chemist's shop.

If possible avoid using denatured alcohol containing additives. Instead,

apply alcohol used for medical purposes.

Never try to drink this alcohol, as it may seriously damage to your health.

Содержание N774 C Series





















































































Результаты поиска

Содержание N774 C Series

Отзывы:

Похожие инструкции для N774 C Series

Бренды по названию

Популярные бренды

Keysight Technologies N774 C Series, Руководство пользователя

Результаты поиска

Содержание N774 C Series

Отзывы:

Похожие инструкции для N774 C Series

Бренды по названию

Популярные бренды