Keysight Technologies N774 C Series Скачать руководство пользователя страница 67

Страница: 67 / 84

Keysight N774xC Series Multiport Power Meter User’s Guide

User Interface Reference

How to Use Auxiliary Functions

How to Get Current Instrument Settings?

The

Home

tab on the N774xC user interface displays the current

instrument settings.

This tab displays the following settings:
•

Description

– Displays the instrument description such as instrument’s

model no., serial no., firmware version and description of the current

instrument.

•

VISA Instrument Address

– Displays VISA instrument addresses of the

current instrument.

•

LAN Details

– Displays LAN configuration details of the current

instrument.

NOTE

Please note that the

Home

tab does not allows the user to change the

displayed instrument settings.

Содержание N774 C Series





















































































Результаты поиска

Содержание N774 C Series

Отзывы:

Похожие инструкции для N774 C Series

Бренды по названию

Популярные бренды

Keysight Technologies N774 C Series, Руководство пользователя

Результаты поиска

Содержание N774 C Series

Отзывы:

Похожие инструкции для N774 C Series

Бренды по названию

Популярные бренды