Keysight Technologies N774 C Series Скачать руководство пользователя

Страница: 68 / 84

Keysight N774xC Series Multiport Power Meter User’s Guide

User Interface Reference

How to Identity a Module?

Sometimes, you have many modules mounted on the rack. In this

situation, it becomes difficult to identify a particular module which are

currently connected.

To identify a particular module, select the check-box

Enable front panel

identification indicator

available on the N774xC

Home

tab. The

Status

LED on the front panel of the connected module will start flashing.

How to Capture an Image of the Graph?

The

Get Image

tab on the N774xC user interface allows you to capture the

current screen of the

Control Instrument

tab and save it as a PNG image.

How to Save/Recall the User Interface Settings?

The

Save/Recall

tab on the N774xC user interface allows you to save and

recall the user interface settings.

NOTE

You can only capture the screen if you are in the

Control Instrument

tab.

Содержание N774 C Series





















































































Результаты поиска

Содержание N774 C Series

Отзывы:

Похожие инструкции для N774 C Series

Бренды по названию

Популярные бренды

Keysight Technologies N774 C Series, Руководство пользователя

Результаты поиска

Содержание N774 C Series

Отзывы:

Похожие инструкции для N774 C Series

Бренды по названию

Популярные бренды