Keysight Technologies N774 C Series Скачать руководство пользователя

Страница: 17 / 84

Keysight N774xC Series Multiport Power Meter User’s Guide

General Operating Considerations

Handling the Instrument

Storage, Carrying and Shipment

Keysight N7744C/5C multiport power meters can be stored, carried and

shipped at temperatures between -40

C and +70

The N7744C/5C multiport power meters must be stored, carried in its

operating position, as shown in

Figure 1

Rack Mount the Instrument

You can mount the instrument in a standard 19-inch rack cabinet using

one of two optional kits, each of which includes instructions and mounting

hardware.

Depending on whether one or two N77xxC instruments are to be mounted,

different mounting kits are required:
• N7799C-1CM Rack Mount Kit 1 HU for 2 instruments - Includes

low-profile rails. Requires Filler Kit N7799C-0CM for single device

(See

Figure 2

• N7799C-0CM Filler Kit for N7799C-1CM - Required for single

instrument. Includes front panel and base plate.

NOTE

Remove the front and rear rubber bumpers before mounting the

instrument on a rack.

Содержание N774 C Series





















































































Результаты поиска

Содержание N774 C Series

Отзывы:

Похожие инструкции для N774 C Series

Бренды по названию

Популярные бренды

Keysight Technologies N774 C Series, Руководство пользователя

Результаты поиска

Содержание N774 C Series

Отзывы:

Похожие инструкции для N774 C Series

Бренды по названию

Популярные бренды