Keysight Technologies N5290A Скачать руководство пользователя страница 7

Страница: 7 / 96

1-1

Keysight N5290/1A PNA/PNA-X Series
PNA and PNA-X Series 2-Port and 4-Port Microwave Network Analyzer

System
Installation Guide

Safety and Regulatory Information

Information in This Chapter

This chapter provides safety information that will help protect you and your

system’s equipment. It also contains information that is required by various

government regulatory agencies.

Chapter One at-a-Glance

Section Title

Summary of Content

“Safety Symbols” on page 2

Descriptions of CAUTION and WARNING symbols used throughout this

manual.

“General Safety Considerations” on

page 3

A list of safety points to consider when servicing your network analyzer.

“Electrostatic Discharge

Protection” on page 7

A discussion of electrostatic discharge (ESD) and related recommendations

and requirements for ESD protection. Also, includes a table of ESD

equipment part numbers.

“Regulatory Information” on page 9

Definitions of instrument markings.
Instructions for disposing of the analyzer’s lithium battery.

“N5292A Test Set Equipment

Ratings” on page 12

Describes the voltage, frequency, and power ratings of your N5292A test

controller

“Environmental Requirements” on

page 13

Descriptions of the environmental requirements that are characteristic for a

system based on the limitations of the PNA network analyzer

“Space Requirements” on page 15

Describes the N5290/1A system weight and dimensions

“Site Preparation” on page 17

Describes power requirement-related information for your N5290/1A

System.

Содержание N5290A

































































































Результаты поиска

Содержание N5290A

Отзывы:

Похожие инструкции для N5290A

Бренды по названию

Популярные бренды

Keysight Technologies N5290A, Руководство по установке

Результаты поиска

Содержание N5290A

Отзывы:

Похожие инструкции для N5290A

Бренды по названию

Популярные бренды